5/18/2023 0 Comments Novation nocturn![]() ? The 8 encoders ‘Control 1-8’ will take control of the first 8 parameters of an Ableton Live Device or all 8 controls of an Ableton Live Rack: ? The Nocturn will now take control of the device ? Click on the title bar of the device/rack with the mouse and a blue hand symbol will appear ? Load up any Ableton Live Device or Rack If you have more than one MIDI map, press the corresponding MIDI button. To access the control map, press the USER button on your Nocturn. Make sure the MIDI Ports are set as follows: It will appear at the bottom of the list.Ħ. The Automap Mapping should look as below:ģ. NOTE: If you unplug and re-plug your Nocturn into a different USB port, then you will need to repeat step 8. Go to File ? Open and select ‘tomap’ from the folder where you copied it to earlier: If only one MIDI channel is active, you will jump straight to the mapping otherwise, if you have multiple MIDI maps, you will be prompted to select a channelĨ. Ensure that at least one MIDI channel is activated:ħ. Ensure that MIDI In is set to Automap MIDI:Ħ. Ensure that MIDI Out is set to Automap MIDI:ĥ. ‘Documents’ folder ? ‘My Automap Mappings’)Ĥ. Copy this file to a folder where you will be able to locate this file more easily (e.g. This is achieved using an Automap MIDI map file.Īn Automap MIDI map file (‘tomap’) has been placed in the same folder as this PDF document:ġ. This document provides a step-by-step guide of how to set up the Novation Nocturn controller to control the Ableton Live Devices and Racks and also interface with the MIDI learn function in Ableton Live. Nocturn Ableton Live Setup Instructions v1.00 I don't have an option to select Nocturn as a control surface? To upgrade from launchpad Live LE license. ![]() PS, once all 4 are set up in Automap, go to FILE>SET AS DEFAULT CONTROL MAP FOR THIS CLIENT, otherwise you have to load up all 4 each time you start it.David Abravanel wrote:Hi, which version of Live are you using? You should be able to find Nocturn as a selectable control surface by going to Preferences->MIDI. Note that some of the pages on the automap software will have more than 1 page - use the page + / - button on the notcturn to switch between them. I have done both as I didn't find all the mappings intuative. You can make changes if you wish in the traktor prefs also, or on the automap side. ![]() Set both IN-PORT and OUT-PORT to AUTOMAP MIDI. Then make sure it is selcted next to "Device". Under DEVICE at the top of that window click ADD and IMPORT the tractor file downloaded above. Now open Traktor, open preferences and go to controller manager near the bottom of the list on the left. Then at the top left corner of the window where it says "Group" you have to re-assign to the relevant button. Choose the desired channgel by pressing the corresponding button on nocturn or double clicking with the mouse. Note when you open the other files they will be assigned to the USER button, when you press the user button you will see options in red for each channel you have added. Repeat these steps with the FX, INST and MIXER buttons, loading the relevent files to channels 2,3,4 respectively. If you make any changes to the naming or configuration be sure to save or it will revert. This should map the controls for that file. Then in the file menu go to OPEN, and open the "Traktor Pro User Channel 1.automap" file. This should open a blank set of controls. Go to SETTINGS>MIDI CHANNELS from the automap software menu and choose Channel 1. Press the USER button on nocturn, the automap window should show "user" at the top and then a blank page with light grey areas for the controls. In the Automap software make sure the main window is showing (press view button on nocturn). This is all done on a mac, if you run PC adjust accordingly.ĭownload the files above and have them ready. I updated to automap 3.7 but I don't think that really affected anything. How do I map a midi chanel to the above groups? I am using automap 3.5, perhaps that is the problem? it seems buggy as when I choose a lot of the menu items there is no response (eg, FILE>OPEN does nothing, nor does save, save as, or most of the big red buttons in the Automap main window). I have done all the previous steps and have loaded the TSI file to traktor, but the above steps I don't know how to do. Load the automap files to each corresponding group I haven't got this hardware working with any other software so I don't know how to program or use the automap software yet, but in your readme file you mention to : It looks like I've finally found something, however I cannot get it to work. ![]() I've just picked up a Nocturn on ebay hoping to use it with Traktor Pro (1.2.4) and have been hunting the internet high and low, but most guides I can find are outdated and no longer relevant.
0 Comments
Leave a Reply. |